Men's Waterproof Windproof Sailing Jacket 300 - Navy
Store Availability
Store Availability
BENEFITS
Water repellent
Specially treated so water slides off the fabric surface.
Resistance to salt water
Materials and zips resistant to salt water and sea air.
Windproof
Fabric specially coated to reduce the cooling effect of the wind.
Waterproof
Tested in moderate rain for 2 hours 5,000 mm Schmerber Pockets not waterproof
Pockets
3 pockets secured with a zip, including 1 inner pocket
Breathability
Very breathable coated fabric (RET < 12): reduces condensation
TECHNICAL INFORMATIONS
Waterproofing 1/2
We measure the resistance of a fabric to water pressure in mm of water column (JIS standard). The higher the water pressure withstood by the fabric, the more waterproof it is.
Here are the waterproofing ratings:
Component resistant to water pressure of 5,000 mm after ageing (five washes). This equates to 5,000 Schmerber (JIS standard), which is the average pressure applied by the water during a rain shower.
The anorak's waterproofing was tested in a rain shower with 60 litres of water / m² / hour for 2 hours.
Waterproofing 2/2 - Technical features of the jacket 300
- Water-repellent coated fabric (water runs off the fabric)
- 100% waterproof seams
- Adjustable jacket bottom with elasticated cord
- Sleeve ends adjustable at the wrist with rip-tab strips.
- Zip fastening protected by internal and external flaps for better waterproofing
- Collar height (back) of 11.5 cm
- Injection-moulded plastic zip to avoid salt oxidation
Hood
The hood can be stored in the collar. The collar is then closed by an injected plastic zip to avoid salt oxidation.
Completely depth and height-adjustable hood: adjustment on the back of the hood and around the neck
Visor with a headband to provide a high level of protection and better maintenance.
The chin-high neck effectively protects the lower part of the face.
Pockets
2 pockets on the front of the jacket, for your VHF, sail tie, cap, etc. Injection-moulded plastic zip to avoid salt oxidation
1 interior pocket on the right of the chest to store your phone or other items, closed with a zip
WARNING: the pockets are NOT WATERPROOF
Front zip closure
Using a zip on the entire jacket length with an interior channel (flap) that protects against the wind and water. The exterior flap reinforces the protection to avoid any water ingress with the zip and guarantees a better waterproofing level.
Soft fabric flap on the top of the collar to protect the chin.
Protection - sleeves
At the end of the sleeve there is an adjustable sleeve with a rip-tab. It lets you adjust the sleeve to your arm length, but also stops air and water coming in.
To easily remove the jacket, open the sleeves
Component Breathability
To find out whether a fabric is breathable, we test its evaporate resistance or RET (ISO 11092 standard). The lower the fabric's resistance, the more moisture is evaporated, and therefore the higher the fabric's breathability.
We consider that if:
RET < 9 = very breathable fabric
9 < RET < 12 = breathable fabric.
The Sailing 300 vest’s RET is 12.
Water-repellent properties information
A fabric is water-repellent when water slides off the surface of the fabric, without seeping in.
Your jacket does not become waterlogged and remains lightweight and breathable. The water-repellent properties are achieved with a treatment applied to the external side of the fabric, but in practice these properties can be altered.
The water-repellent properties can be reactivated by putting the anorak in a dryer for 10 minutes at the lowest temperature.
How to wash your jacket?
To maintain the water repellent properties, infrequent washing is recommended.
Close all zips and flaps, empty all pockets and then turn the garment inside out to wash it. You can wash it on a synthetic cycle at 30°C or 40°C with your usual detergent. Do not use fabric conditioner, which could damage the existing performance of the garment, or bleach. Very important: choose a full-rinse cycle or extra rinse.
How to reactivate the anorak's water repellency
Drying is a crucial phase in reactivating the water repellent treatment.
We recommend that you lay your anorak flat on a clothes rack and leave it out to dry in the open. Caution: never dry your anorak directly on a radiator.
Then place it in the tumble dryer on a short synthetics cycle, i.e. 10 to 15 minutes, before turning it back the right way round. Caution: do not over-dry the garment.
composition
composition
Lower part - Main fabric: 100.0% Polyamide; Upper part - Main fabric: 100.0% Polyamide; Main lining: 100.0% Polyester; Secondary lining: 100.0% Polyester; Coating: 100.0% Polyurethane
Tips for storage and maintenance
MAXIMUM WASHING TEMPERATURE 30°C. NORMAL TREATMENT.
BLEACHING EXCLUDED.
DRYING IN TUMBLE DRYER POSSIBLE. LOW TEMPERATURE, MAXIMUM DRUM EXHAUST TEMPERATURE 60°C.
DO NOT IRON.
DO NOT DRY CLEAN.
TESTS AND WARRANTY
Warranty
2 Years